+8615824687445
Home / Knowledge / Details

Oct 21, 2026

NM550 Wear-Resistant Steel Plate Properties and Applications

NM550 is Chinese quenched & tempered low-alloy wear-resistant steel plate to GB/T 24186. "NM" means wear-resistant, and 550 refers to its nominal Brinell hardness of 550 HBW, with actual hardness ranging 520–580 HBW. It delivers outstanding abrasion resistance and balanced toughness. It suits mining, quarrying and cement sectors for chute liners, excavator bucket edges and crusher wear parts. Proper preheating is required for cutting and welding. It extends equipment service life under heavy friction and moderate impact, commonly equivalent to Hardox 550.

 

NM550耐磨钢板| 550 HB耐磨钢板

 

NM550 Chemical Composition(GB/T 24186)

 

 

NM550 low-alloy wear-resistant steel adds Cr, Mo, B microalloys. Controlled carbon and impurity levels improve hardenability. This chemical design achieves high surface hardness while retaining acceptable weldability for mining & quarry components.

 

Element Content (wt%, max)
C 0.38
Si 0.70
Mn 1.70
P 0.020
S 0.010
Cr 1.20
Ni 1.00
Mo 0.70
Ti 0.05
B 0.0005–0.006

 

 

NM550 Mechanical Properties(GB/T 24186)

 

 

NM550 obtains these properties via quenching and tempering. High hardness delivers superior abrasion resistance. It maintains enough toughness to resist moderate impact, commonly used for chute liners, bucket tips and crusher wear parts.

 

Property Value
Brinell Hardness 520–580 HBW
Yield Strength ≥1250 MPa
Tensile Strength ≥1450 MPa
Elongation A50 ≥8%

 

 

NM550 Processing Key Points

 

 

Welding: CO₂ gas shielded welding is recommended. Preheating at 150–200°C is required for plates with thickness ≥20 mm.

 

  • Before welding, remove contaminants such as oil, moisture and rust within 50 mm on both sides of the weld groove.
  • Mixed gas shielded welding shall be adopted; shielding gas composition: 80% Ar + 20% CO₂.
  • Solid wire is recommended. Low-hydrogen or ultra-low-hydrogen welding wire is preferred. Hydrogen removal treatment at 150–200°C for 2 hours can be performed if conditions permit.
  • Welding heat input shall be controlled at approximately 10 kJ/cm. Narrow-gap welding is applied. Interpass temperature shall be kept below 300°C. Thermal insulation is required after welding.

 

Cutting: Multiple cutting methods are available, including flame cutting, laser cutting and plasma cutting.

 

Heat treatment: Quenching temperature shall be controlled within 780–850°C, followed by low-temperature tempering at 200–250°C. This relieves stress while preserving high hardness.

 

 

NM550 Wear-resistant Steel Hardness Test:

 

 

Portable handheld hardness testers calculate hardness by measuring the rebound velocity of the impact body after colliding with the material surface. This method imposes strict requirements on flatness, rigidity and fixation stability of the test surface. For thin plates (especially steel plates ≤16 mm), elastic deformation may greatly affect the transfer of impact energy and the accuracy of rebound velocity, resulting in lower readings or increased data scatter.

 

Carbide precipitation in tempered martensite within the heat-affected zone from flame cutting reduces hardness. For samples taken from flame-cut edges, specimens of plates ≥20 mm thick shall be no less than 200×200 mm; specimens of thin plates <20 mm shall be no less than 250×250 mm.

 

The oxide layer of 1.2–1.5 mm on the surface must be ground off before testing.

 

 

M550 Wear Resistant Steel Plate | Main Applications

 

 

Mining Industry Used for crusher liners, hopper walls, chute liners, bucket guards and screening plates. It withstands continuous particle abrasion and moderate impact from ore, rock and gravel, extending service life of mining handling equipment.

 

Construction Machinery Applied to excavator bucket edges, loader wear plates, bulldozer blades and scraper components. It resists scratch and impact wear from sand, stone and soil on earthmoving sites.

 

Metallurgical Plant Equipment Suitable for blast furnace feeding chutes, converter lining guards and continuous casting wear plates. It handles high-temperature material scouring and abrasive wear under metallurgy production conditions.

 

Cement Industry Used for cement mill liners, separator blades and raw material transfer hoppers. It fights persistent abrasion caused by cement clinker, mineral powder and granular raw materials.

 

Coal Power & Bulk Material Handling For coal feeder liners, coal bunker plates, conveyor skirt boards and dust cyclone wear parts. It works under long-term friction from coal, ash and granular bulk solids.

 

Waste Recycling & Quarrying Suitable for stone crusher wear parts, waste shredder liners and sorting equipment, resisting wear from hard rock and solid waste impact.

 

NM550 Wear-Resistant Steel Plate   

You Might Also Like

Send Message